Powerline carrier PowerLink IP
PowerLink IP – the PLC solution for digital transmission grids
Powerline carrier PLC systems utilize the high-voltage line(s) between transformer substations as a cost-effective communication path for data, teleprotection, and voice. Siemens power line carrier technology has been applied over decades, ensures extremely high standards of transmission reliability in network protection (such as protection signals), safeguards the transmission quality, and can easily be integrated into a wide range of communication networks. PowerLink IP has been designed for the Ethernet / IP environments of the new digital high-voltage substations and makes PLC systems today more attractive and efficient than ever before.
For the communication requirements of modern substationsThe new PowerLink IP system has a pure packet-based architecture that is optimized to fulfill the communication requirements of modern substation devices. The integrated SWT 3000 teleprotection system provides binary I/O and Goose (IEC 61850) interfaces.
HV powerline carrier systems typically operate in the frequency range up to 500kHz. Classic HV PLC systems make use of bandwidth of up to 32 kHz per system, providing a data rate of up to 320 kbps. In contrast to classic PLC systems, PowerLink IP utilizes a frequency band of up to 256 kHz, allowing a maximum data rate of up to 2 Mbps per transmission direction. In addition to the expanded frequency band, the completely newly developed, efficient bandwidth utilization is the core functionality of the PowerLink IP system.
Parts of the frequency band can be blocked (notched) within the channel band of a PowerLink IP system. This feature allows higher data rates because the PowerLink IP frequency band can be extended beyond blocked (e.g. radio) frequencies.
In case a part of the PowerLink IP frequency band is disturbed, additional frequency bandwidth can be requested from other PowerLink IP systems, if available. This feature ensures the maximum data throughput for all PowerLink IP systems in case of external disturbances.
Asymmetrical communication option
The dataflow of digital substations is often asymmetric (upstream > downstream). The data upstream and downstream channels of PowerLink IP can be adjusted to these different bandwidths This option allows the adaptation of the data throughput to the special requirements of modern grid applications.
PowerLink IP – the cost-effective communication solution
Although the main transmission lines are usually equipped with fiber optic cables, there are many HV substations where the installation of fiber is not cost effective. Additionally, PowerLink IP provides the requested bandwidth to replace alternative communication solutions (e.g. radio).
PowerLink IP – the backup communication solution
In this solution, the primary communication path is provided by Ethernet over SDH (synchronous digital hierarchy) or MPLS (multi-protocol label switching) systems.
PowerLink IP acts as a reliable back-up path for the most important grid applications.
This effective combination of fiber optic communication technology with broadband PowerLink IP provides the highest reliability for transmission needs of critical HV links.
PowerLink IP – the perfect solution for the smooth migration of classic to digital substations
In many cases, transmission utilities do not intend to replace all legacy devices in an HV substation at one go with state-of-the-art, Ethernet-based equipment. Instead, they prefer a smooth, phased migration of the affected devices. PowerLink IP offers two general options to support these requirements.
Integration of legacy devices via gateway/router
If PowerLink IP is the only PLC system in the substation, the connection of legacy devices like analog phone, IEC 60870-5-104 RTU, etc. takes place via a small gateway/router system, which converts interfaces like analog voice, V.24, X.21, E1, etc. into Ethernet/IP protocol. All new substation devices with IP/Ethernet interfaces can be connected directly to PowerLink IP.
Co-existence of classic PLC and PowerLink IP
Furthermore, classic PLC systems can be used in parallel to a new PowerLink IP system on the same powerline. In most cases, the new PowerLink IP system can also be connected to the existing coupling capacitor, line trap, and coupling unit. The classic narrow-band PLC provides the communication link for the remaining legacy devices, while the new IP/Ethernet-based devices will be connected to PowerLink IP. PowerLink IP, and existing classic PLC systems will utilize different frequency bands, thus allowing undisturbed, parallel operation of all devices operated on an HV line.
Easy-to-operate – the PowerLink IP management system
Intuitive and easy-to-operate, PowerLink IP uses commercial web browsers for the system administration. Thus, no additional software installation is required for administration or operation. The administration of a remote PowerLink IP system can be easily performed from the local operator console or via the corporate LAN network. The state-of-the-art encryption technology for IP packet-based transmission is complemented with access restrictions to the device´s web-based administration portal by user log-in and password. This safeguards the PowerLink IP communication applications. This user interface is designed for desktop and mobile devices and is also suitable for touchscreen operation of the type available on modern equipment such as tablet PCs.
The strengths of PowerLink IP – your benefits:
- PowerLink IP provides proven PLC technology for the extended bandwidth requirements of digital high-voltage substations
- Data rates of up to 2 Mbps allow to replace several PLCs
- The core feature is an expanded and more efficient bandwidth utilization
- The pure packet-based architecture reduces installation and maintenance effort / training
- We offer tailor-made solutions for primary and backup HV substation interconnections
- Seamless integration into existing PLC infrastructure
- PowerLink IP provides custom migration scenarios for the integration of legacy devices
- Siemens supports a smooth transition with product-related services along the implementation path
- PowerLink IP is prepared for future software applications and maintains its role as a trendsetter in modern PLC technology – now and into the future
New challenges for energy networks
In terms of the decentralization of energy supply, the reliable management of power supply systems is becoming increasingly challenging. This development goes hand-in-hand with the rapid growth in demand for communications. Solutions are manifold – but we put it all together: with a secure, reliable, and cost-effective power supply that is closely linked to a fast, efficient, and dependable communications infrastructure. Do you want to know more about telecommunications and energy technologies? Click here for our free manual.