Industrial Trent 60 aeroderivative gas turbine

SGT-800 Industrial Gas Turbine

up to

0 MW
  • power generation


Most powerful, pure aeroderivative gas turbine in its class

The Industrial Trent 60 has established a new benchmark for power output, fuel economy, and cost savings. The gas turbine is highly flexible, offering high power and efficiency with minimal drop-off at part-load and reduced speed conditions. It is available with Wet Low Emission (WLE) and Dry Low Emission (DLE) combustion systems. 

Highlights of the Industrial Trent 60 gas turbine

Due to its three independent shaft design, the gas turbine is highly flexible, offering high power and effiency with minimal drop-off at part-load and reduced speed conditions.

For a simple cycle Industrial Trent 60 package, the start-up sequence time is designed to be less than 10 minutes from pressing the start button to reaching full baseload. This includes an allowance for simple cycle exhaust system purge. 

The Industrial Trent 60 has the most mechanical drive experience in its class and is ideally suited to meet the higher power, variable speed demands required by applications such as natural gas liquefaction, gas transportation, and gas induction for oil recovery. 

One of the most efficient gas turbines on the market, the Industrial Trent 60 provides up to 66 MW in simple cycle service at 42.5% efficiency. Its cold start capability and high cyclic life allow it to add power to the grid very rapidly to compensate for the fluctuations and variability of renewable and other power sources, making it ideal for peaking markets.

The Industrial Trent 60 consists of eight engine modules for easy maintenance. Each module is pre-balanced to provide complete interchangeability.

The Inlet Spray Inter-cooling (ISI) system provides performance improvements at ambient temperatures greater than 7° C (52° F), while minimizing the additional plant water consumption and auxiliary load compared to other inlet cooling technologies with comparable performance enhancement. 

Ingenious design to the core

The flexible design allows to use the same engine for power generation as well as mechanical drive service with no changes. The mechanical arrangement uses three co-axial independently rotating shafts contained within a carcass of axially joined circular cases. 

Industrial Trent 60 packages

The package is designed for quick installation and easy maintenance in the field.

The package contains all components and subsystems that have been carefully selected and optimized to support the Industrial Trent 60 gas turbine:

Gas turbine, enclosure, base frame, air intake, exhaust collector, engine control system, fuel metering skid, lubricating systems, starter system, vibration monitoring system, fire fighting system, package ventilation system, instrumentation, gearbox (if needed)

SGT-800 based power plants

For combined cycle and cogeneration (combined heat and power - CHP), Siemens offers a broad range of power plant configurations and scopes based on the SGT-800 gas turbine. For combined cycle, 1x1, 2x1, or 3x1 configurations are part of the standardized portfolio.

Engine change-out in under 24 hours

Our service offerings include Long Term Programs (LTP), overhaul services, field service, spare parts, reconditioning of components and modernization and upgrades. 

Maintenance of the Industrial Trent 60 engine can be accomplished quickly and easily due to the aero engine design. 

Siemens specialists offer on-site support all over the world.

Fuel flexibility matters

DLE - 34 to 48 WI / WLE - 34 to 52 WI

Liquid Fuel Operation

Due to the aeroderivative heritage, the Industrial Trent 60 can operate on liquid fuels without an EOH "equivalent operating hour" penalty. In fact, the Industrial Trent has exhibited complete liquid operation without performance or component life degredation. 

Designed to meet stringent environmental requirements

The Industrial Trent 60 DLE (Dry Low Emissions) engine is designed to meet stringent environmental requirements. 

The use of eight radial staged combustors allows the successful operation of the engine in part load operation while still maintaining NOₓ and CO compliance. 

NOₓ emissions:  ≤ 25 ppmvd on fuel gas (with WLE and DLE, at 15% O₂)

Technical data

Industrial Trent 60 DLE: Performance data for simple cycle power generation

Industrial Trent 60 WLE ISI: Performance data for simple cycle power generation

*Other fuels on request; automatic changeover from primary to secondary fuel at any load

**NOx emissions at 15% O₂ on fuel gas (with DLE)

Performance data for combined cycle power generation / 50 Hz

Performance data for combined cycle power generation / 60 Hz

 Industrial Trent 60 WLE - water injected. ISI - Inlet Spray Intercooling. All combined cycle performance is based on 2 pressure, no reheat.

Performance data for mechanical drive

*Other fuels on request; automatic changeover from primary to secondary fuel at any load

**NOx emissions at 15% O₂ on fuel gas (with DLE)

Note: Industrial Trent 60 WLE - water injected

Physical dimensions and weight

For power generation, AC generator is included, dimensions include inlet filter housing, exclude exhaust stack.

For mechanical drive, driven equipment is excluded, dimensions exclude inlet filter housing and exhaust stack.


More than 100 units installed worldwide

The Industrial Trent 60 gas turbine is in operation for decades with hundreds of installations worldwide.

Downloads and support

Find out more about our products and services

Find brochures, technical papers and more in our download section, or contact us directly for specific inquiries

For more information, please contact our Customer Support Center.


Industrial Trent 60 reference highlights



Do you have a question regarding our products, solutions and services? To contact us, simply fill out our inquiry form.

Contact form

Contact form